.. ..The instruction SUB AX, BX, gives the result of ....... In register. Explain the given question with an example. Not just copy paste answer.
Q: Determine the current I for each configurations of circuits using the approximate appropriate model…
A: ac
Q: Give an example problem of "SECOND ORDER PASSIVE BAND PASS FILTER"
A: Example for "SECOND ORDER PASSIVE BAND PASS FILTER" :- In passive filter only passive components…
Q: Compute the power factor and the reactive factor for the network inside the box in Fig. 10.6, whose…
A: It is given that: a.v=100cosωt-45° V;i=20cosωt+15° Ab.v=100cosωt-45° V;i=20cosωt+165°…
Q: A single-phase induction motor draws a current of 0.5 A at 230 V and 0.6 lagging p.f. If it runs at…
A: It is given that: V=230 V;I=0.5 A;Cosϕ=0.6 lagging;ω=100 radsOutput torqueTout=0.3 Nm
Q: To obtain a stepping angle of 7.5° for a 3-phase PM stepper motor, how many poles should the rotor…
A:
Q: What is the force between two small charged spheres having charges of 2 x 10-7 Cand 3 x 10-7 C…
A: Two small, charged sphere having, Charge, Q1=2×10-7 C. Charge, Q2=3×10-7 C. Placed apart a distance,…
Q: was wondering if you could give me the names of the three basic frequency bands that are utilized in…
A: We need to tell about three basic frequency bands that are utilized in wireless communication…
Q: For the system shown in the figure below, find the sensitivity of the steady-state error for changes…
A:
Q: A dielectric material has relative permittivity of 9 and the loss tangent is 10-³ at 50 MHz, the…
A: Given- A dielectric material- Relative permittivity = 9, Loss tangent = 10-3 at 50 MHz. To Find- The…
Q: Calculate the Fourier series of the function 0, when - ≤ t ≤0 f(t)=t, when 0 ≤ t ≤ -t, when≤tst.
A: Given: A periodic function f(t) with period 2π, defined over a period as,…
Q: 1. We are transmitting a digital signal whose logic levels are A (volts) and B (volts) where A<B.…
A:
Q: V= A 2.5 A R₁ = ? www Vy= 6.0V R₁ = 13.00 R₂ = 15.052 = 10.052 Find the ff V₂ = ? 4 = v₁ = V₂₁ V₂ 11…
A:
Q: s) = 5652+St5
A: I have written this solution as handwritten solution. Hope you find the perfect solution.
Q: 5. A double circuit, single-phase transmission line is shown (Fig. 2). Show that the 2KD √1+k²x10-7…
A: Inductance of Single Phase Two Wire System: A single phase two wire inductance system consists of…
Q: A 208-V, 45hp, 0.85 pf leading, delta-connected, 60 hz synchrounos machine has a synchronous…
A: Given Data: A synchronous machine with, Voltage rating V=208 V Power rating P=45 hp Power Factor…
Q: 9 3. An infinite uniform sheet charge with ps = 5π nano C/m² is located at 25 z = 7 meters and an…
A:
Q: Que:29 22+7i volts and the current through the element is 5-4i amperes, determine the impedance and…
A:
Q: UPSs have two main kinds.
A: The given statement is written below. UPSs have two main kinds. We need to mention the types and…
Q: Find I, using the method of source transformation. j4_n GO LO V 2. M 65 W -jan 4 -јзл +4 5490° A
A: The given circuit is We need to find the current Ix by using the source transformation.
Q: In a uniform linear array, four isotropic radiating elements are spaced apart. The progressive phase…
A: I have written this solution as handwritten solution. Hope you find the perfect solution.
Q: Explain how an oscilloscope and signal generator are used in a lab?
A: In this question we discuss how an oscilloscope and signal generator are used in a lab.
Q: 2. The Equivalent Circuit referred to the LV side of a 480/120 V, Single phase Transformer…
A:
Q: A sinusoidal alternating current of frequency 25 Hz has a maximum value of 100 A. How long will it…
A: Given: Im=100 A, f=25 Hz,i=100sin2πft,i=100sin50πt.
Q: A 2.2-kVA, 440/220-V, 50-Hz transformer has the following parameters as referred to the primary…
A: In this question we need to find the efficiency and the voltage regulation of the transformer. We…
Q: In the above circuit, the initial conditions are all zero and the op-amp is ideal Vo(a) in one of…
A: The filter circuit is given as By virtual ground concept,Va=Vb=0V
Q: A long, straight wire carries a current | = 10A. At what distance the magnetic field is 5 A/m? A…
A: A long straight wire, Current carries, I=10 A. Magnetic field intensity, H = 5 A/m.
Q: R₁ 10 ΚΩ R2 Μ Vcc = 10 ν Rc 1 ΚΩ RE 560Ω
A:
Q: c. Draw a circuit diagram with an encoder and decoder that will output the 1's complement of the…
A: I have written this solution as handwritten solution. Hope you find the perfect solution.
Q: Question 7 With the assumption that the switch in the circuit of Fig. 8.54 has been closed a long,…
A:
Q: Examine the discrete-time system: y (n) = x(n) I then determine which of the following properties…
A: Given Data: A discrete-time system of, yn=xn To Verify: Static or Dynamic Linear or Non-Linear TIV…
Q: 12. For the unity-feedback system of Figure P8.3, where K s(s+5)(8 + 8) plot the root locus and…
A: The root locus can be drawn based on the location of poles and zero in the given system. The locus…
Q: Determine the Nyquist sampling rate for the following signals: (a) 4 sinc(420πt); (b) 5 sinc²…
A: As per Bartleby guidelines, as more than 3 subparts are present in the question, only the first 3…
Q: What is the total amount of memory necessary (in Bytes) to create a 3 x 4 x 2 array of chars…
A: What is the total amount of memory necessary (in Bytes) to dynamically create a 3 x 4 x 2 array of…
Q: 1. Expand f(x) = 0 if 0 < x 1 if TT 2 in a half-range: (a) Sine series. (b) Cosine series. < < x <…
A:
Q: 3. The electric field of a plane wave is given by E = â 3 cos(@t-kz+75) xe-² V/m and the…
A: Answer : given that the electric field of the plane wave is given by E→ =a^x 3cosωt-kz+75°×e-αz V/m…
Q: Q.8 F1 =A’B + BC’ + ABC’ + BCD F2= (A’ + B) (A + B + C’) (A + D) And If F= F1.F2 Obtain minimized…
A:
Q: Problem 02: 1.1 Develop Signal Flow Diagram 1.2 Use Mason Gain Formula to Determine Y/R
A: The given block diagram should be converted into signal flow graph by considering summing and pick…
Q: 4 DTFT A discrete-time Linear Time Invariant (LTI) system has impulse response h[n] given by h[n] =…
A: Given: Impulse response of a DT LTI system, h[n]=u[n-2]-u[n-8], And frequency response of the…
Q: The current through the 2 kn resistance in the circuit shown is A Μ 1 ΚΩ 1 ΚΩ C '2 ΚΩ D 1 ΚΩ 6 V 1…
A: The DC circuit,
Q: What is the maximum range of your radar if you require a S/N of 13 dB given the following: Transmit…
A:
Q: 1. A communication system uses Quadrature Phase Shift Keying (QPSK) modulation for transmission. 1)…
A: Quadrature phase shift keying (QPSK) is another modulation technique, and it’s a particularly…
Q: Calculate the power delivered to 3 ohms resister in the circuit? 18 V 14.2 W O 1.33 W O 28.4 W O 5.5…
A:
Q: The figure below shows the rotor current of a PMDC motor immediately after a 12V source is connected…
A: Given : Rotor current v/s Time curve Back emf constant,ke=30 mV/rad/s Supply Voltage VT=12 V To…
Q: The input x(t) and output y(t) of a system is described by the following equation y(t) = [5+cos (t))…
A:
Q: 4. The op amp in the noninverting amplifier circuit below has an input resistance of 400 kn, an…
A: As per Bartleby's guidelines, only first 3 subparts can be solved. Please send other subparts…
Q: 3. A transition table is given below. Draw the state diagram the table represents.
A: The given transition table can be converted into a state diagram using the mealy machine method. The…
Q: 1 of 1 If V = 25 V is applied across the whole network(Figure 1), calculate the voltage across each…
A:
Q: 6.0 Ω 24 V www.il www 6.0 Ω ww 15 Ω 4.00
A:
Q: Examine the discrete-time system: y (n)=x (2n) then determine which of the following properties they…
A: Given Data: A discrete-time system of, yn=x2n To Check: Static or Dynamic Linear or Non-Linear TIV…
Q: Solve for the node voltage shown in the figure below. Assume R= 20 Ω. (Figure 1). Enter your answers…
A:
Step by step
Solved in 4 steps
- Supnorting.cxcentions &interruats Select True/False (T/F) for each statement. Exception usually refers to an event outside of the CPU and interrupt refers to an event inside the CPU. ISelect The CPU checks for exceptions/interrupts after every assembly instruction to get to them tast. Select With polled interrupts, the hardware is responsible to identify the source of the event. Select) With vectored interrupts, the hardware is responsible to identify the source of the event. I Setect)Q5: Fill in the following blanks with appropriate answers (Choose Five Only) 1. The instruction that subtracts 1 from the contents of the specified register/memory location is ..…….….…..………………….. 2. In general, the destination operand of an instruction can be ....... 3. The instruction that supports addition when carry exists is 4. If there is a carry from lowest nibble during addition, ............. flag sets. 5. register is used as a default counter in case of string and loop instructions. 6. In PUSH instruction, after each execution of the instruction, the stack pointer is. ************** **********Q1. Design a circuit of General register organization in which 4 registers are there from R0 to R3. (a) Explain the control word as per the register configuration given above.
- An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 Me example to each one of application of microprocess.. 2/ Write the contents of flag register after execute the following operation (AC)16 + (3B)16-(B)- Answer the following questions: 1. After the PUSH and POP instructions, where does the stack pointer go? 2. Explain the opcode and operand in XCHG [BX||SI]+1234H, AX instruction. 3. If DX contains 81FEH and CX contains 1986H, explain the effect of the following instructions on the flag registers. Suppose that the flags are initially 0 in each statement of this question. i.SUB DX, CX ii.ХСHG DX, Cх
- d) This addressing mode is always used to access memory, shown here as the source operand of this instruction: LDR R1,[R0]?- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it6. Describe the operation of an OTE instruction.
- 1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 11. An 8-bit register contains the number 10000110. The serial number 11011011is applied to the input. After 5 shift pulses, what is the number in the shift register? Assume shift right operation 2. A binary number is shifted 5 positions to the left. The number therefore has been 3. A binary number must be divided by 128. How many positions must the number be shifted (and in what direction to achieve this?Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.