helpSubjective Questions 1.5. What is quality of conformance from the producer'sperspective and how can it be achieved? 1.6. A company has accepted a contract to producea special electric motor. The number of direct labor hours required to produce the first motoris 250. If an 85% learning curve applies to the production of motor, then the number oflabor hours needed to produce the 4th motor is? 1.7. The direct labor times required toproduce the first four units of a new product are shown below Based on this data, what is theestimated learning or improvement rate? R Subjective Questions1.5. What is quality of conformance from the producer's perspective and how can it beachieved?1.6. A company has accepted a contract to produce a special electric motor. The numberof direct labor hours required to produce the first motor is 250. If an 85% learningcurve applies to the production of motor, then the number of labor hours needed toproduce the 4th motor is?1.7. The direct labor times required to produce the first four units of a new product areshown belowUnit Number Direct Labor Hours1,2001,020927.5867Based on this data, what is the estimated learning or improvement rate?1234

A learning curve is a graphical representation that shows how an increase in learning (measured on…

Answered: 1.5. What is quality of conformance…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

11. PJ Sumeguin, Inc. produces telephone system with built in TV screens. Its learning rate is 80%.a. If the first one took 56hrs, how long will it take the company to complete the 11th unit?b. How long will the 1st 11 systems take in total?c. If you are the purchasing agent, you are expected to buy units 12 through 15 of the newphone systems. What would be your expected cost for the units if company charges $30for each labor hour?
State the approches to solve learning curve problems?
On RainTite Window’s manual assembly line, a newemployee can usually assemble their first window unit in30 minutes. Management assumes a 90 percent learning rate.a. How long should a new employee take to assemble theirsecond window if management is correct in their assump-tion? How long should the 16th window take?b. On RainTite’s semi-automated line, a new employeetakes 45 minutes to assemble their first window; however,the learning rate is 75 percent. At how many windowsproduced will the semi-automated line’s employee takeless time to produce a window than an employee on themanual line?
critically analyuse the provided diasgram and examine each of the phases in the system model of training and development , designed to add value to the organsiastion and increase employee capability , to regain a good return on invesdtment
State the limitations of learning curve?
Q3: Why training needs assessment at organizational, job and individual level? Give one appropriateexample that summarizes all levels. This is the question of Human resources management
4. A new electronic component produced for an oil drill rig took 40 hours for the production of the first unit. If the production process has an 85% learning rate, calculate the following: a. The estimated time required to produce the first five units b. The time estimate for producing the 25th unit
Name three approches that are used to solve the learning curve problems ?
A) A company working on an 80 percent learning curve has decided that the production standard should be 90 hours the first unit? Show detailed solution i of production for the 128th unit. How much time should be required for B) In a job shop, effective capacity in only 50 percent of design capacity, and actual output is 90 percent of effective of 9 jobs per weeks? Show detailed solution capacity. What design capacity would be needed to achieve an actual output C) You are an engineer who has been assigned a task to perform a HAZOP (Hazard and Operability) study on a Reactor used as main equipment in a certain chemical production plant. i. What are the steps to be followed to perform this study? ii. Use a table to give an example of the parameters, related guide words and deviations that could be used to develop this study.
On the Job Applied Case Study (Mira Sermanissian)Mira Sermanissian is the Human Resource Director for a manufacturer of airline part in Montreal.The environment of the company is one of high stress, due in part to the necessity to produceparts with no errors. Because the company operates in a “just-in-time environment, there is noinventory and the parts not only must perfect, they must be produced on demand. This need forprecision and timelessness has resulted in an environment that some employees compare to thatof brain surgery. As a result of this tension, Sermanissian realized that she needed to take stepsto ensure that stress would not affect the physical and psychological health of the firm’semployees.(Source:Micheal G. Aamodt (2017) Industrial/ Organizational Psychology: An Applied Approach, 8th Edition, Cengage Learning) a) If you were Sermanissian, what would you do to help to prevent the effects of stress?b) If stress is not reduced, what are the potential consequences for the…
Jericho Vehicles is considering making a bid for a mobilerocket-launching system for the U.S. military. However,the company has almost no experience in producing thistype of vehicle. In an effort to develop a learning curvefor the production of this new mobile weapon system, management has called contacts from several former competitors who went bankrupt. Although management couldnot obtain direct learning curve rates, they did learn fromone contact that for a system with similar features, the firstunit required 2400 hours of direct labor to produce and the30th and final unit required 1450 hours to produce. Determine the learning curve rate for this vehicle.
1.What is cycle time? Break down it into its components and define each. Which of them are characterized as valued-added time. 2. Describe the concept of Business Process Re-engineering (BPR). 3. Identify some advantages and disadvantages associated with BPR.

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS