Answer the question considering the information given in the pictureD)What would happen to the difference in height in the two piezometric tubes if the oil is changed for another liquid, with different density and viscosity, maintaining the same flow rate? Explain qualitatively in which case it can increase, decrease or remain the same. 2. In a 0.32 cm diameter pipe, motor oil passes and is released into theatmosphere with a flow rate of 0.20 ml / s. At a temperature of 20 °C,the viscosity of the oil is 30.0 x 10-3 Pa -s and the density is 800 kg /m3. To measure the pressure drop, two piezometric tubes or gaugesare placed 25.0 cm apart as indicated in the figure.Ah25 cmFigure 2. Pipeline that carries oil with piezometric tubes 30 cm apart

Given: To find: For diff liquid what will happen

2. In a 0.32 cm diameter pipe, motor oil passes and is released into the atmosphere with a flow rate of 0.20 ml / s. At a temperature of 20 °C, the viscosity of the oil is 30.0 x 10-3 Pa ·s and the density is 800 kg / m3. To measure the pressure drop, two piezometric tubes or gauges are placed 25.0 cm apart as indicated in the figure. 25 cm Figure 2. Pipeline that carries oil with piezometric tubes 30 cm apart

2. In a 0.32 cm diameter pipe, motor oil passes and is released into the atmosphere with a flow rate of 0.20 ml / s. At a temperature of 20 °C, the viscosity of the oil is 30.0 x 10-3 Pa ·s and the density is 800 kg / m3. To measure the pressure drop, two piezometric tubes or gauges are placed 25.0 cm apart as indicated in the figure. 25 cm Figure 2. Pipeline that carries oil with piezometric tubes 30 cm apart

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at temperature of 20 °C is flowing inside a straight, smooth pipe with flow rate of 0.05 m3/h . With which pipe diameter will the flow transition from laminar to turbulent? Kinematic viscosity of water at 20 °C is 1.005·10-6 m2/s. Round off the answer to one decimal digit in cm, but enter the answer without the unit.
The pressure drop (Ap) test is carried out using a pipe configuration as illustrated below: Manometer 1 Manometer 2 straight pipe D= 2R R= radius in pipe The pipe data and the flowing fluid are as follows: Pipe: D = 1 cm; L= 100 cm. Fluid: Water, with density (A) = 1000 kg/m"; absolute viscosity (u) = 0.001 kg/im.s); Experimental data is shown as shown in the following table: Task: Ja. Plot the graph of the pressure as a function of the average velocity (V.v). b. Based on the equation for laminar flow in the pipe as follows: Ap = 32VuL, Vavg (m/s) Ap (Pa) 0,001 0,002 0,005 0,01 0,02 0,04 0,06 0,08 0,1 0,12 0,15 0,30 0,62 1,61 3,10 6,10 12,10 20,10 26,00 32,50 38,90 47,20 D Compare the experimental results in the table with the results of calculations using the above equation. Leave a comment. Note: Ap = p1-p2. c. The coefficient of friction (f) in the pipe is formulated as follows: f- 2DAD PL(V.) plot (plot) this distribution of fas a function of the Reynolds number (Re). Re is…
A small capillary with an inside diameter of 2.22 x 10-3m and a length 0.317m is being used to continuously measure the flow rate of a liquid having a density of 875 kg/m3 and viscosity of 1.13 x 103 Pa-s. The pressure drop reading across the capillary during flow is 0.0655m water (Density is 996 kg/m3). What is the flowrate in cu.fps?
A catheter-sensor system for invasive pressure measurements has a catheter with a length of 1 m and a diameter of 2.5 mm. The catheter is filled with water at 20 C, with viscosity  = 0.001 Pa.s and density  = 103 kg/m3. The diaphragm elasticity Ed equals 0.5x1015 N/m5. a. Draw the simplified electrical model of the pressure measurement set-up that includes the catheter and the diaphragm and determine the transfer function of the pressure measurement system. b. Compute the natural frequency and damping ratio of this system. c. The current system has a damping ratio that is far from optimal. Suppose you are pinching the catheter for a small length lx so that the catheter diameter reduces to 0.2mm. Assuming the pinch to affect the resistance only, determine the length lx such that an optimal damping ratio  = 0.7 is obtained. d. Suppose that the assumption of purely resistive effects of the pinch cannot be made. Discuss (without calculations) the consequences on the derivation of lx.
A well with 4 in. radius produces oil with a viscosity of0.3 cP, at a rate of 200 barrels/day, from a reservoir that is 15 ft.thick. The pressure in the wellbore as a function of time is: t (mins) 1 5 10 20 30 60 Pw(psi) 4740 4667 4633 4596 4573 4535 Use the "semi-log straight line" method to estimate the permeability, K
At a point in a pipe that lay flat ノ water in the pipe flows at a speed of 9.0 mls and has 6-40x 104 Pa a gaoge pressure is Find the gauge pressure at point 2 of pipe that lower than the first point 8.0 m and the cvoss - se ctional| area of the pipe is double of first point . Answer [1.52x105 Pa]
What is the behavior of flow if water at 20 deg C is flowing through a pipe with a radius of 2.067 in at 20 gal/min. Viscosity of water at 20 deg C =1.005 cP Density of water at 20 deg C = 998.23 kg/m3
Calculate pressure loss in a pipe ( d = 55 mm, L = 200 m ), for oil mass flow rate of 133 kg/min. Oil density is 900 kg/m3and kinematic viscosity is ν = 4·10-5 m2/s. The sum of local losses in the pipe is 3,5. Round off the answer to one decimal digit in kPa, but enter the answer without the unit.
Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the velocity, in meter per second (m/s), of water inside the pipe is Blank 1 **EXPRESS YOUR ANSWER IN TWO (2) DECIMAL PLACES**
The laminar flow of a fluid with a constant viscosity, 4, inside a channel is governed by the following boundary value problem (strong form): d'u dp for y E (0, h) "dy dr u = 0 at y = 0 and y = h vhere u is the fluid velocity and is the pressure drop in the direction of the flow. a) Derive the weak form of the boundary value problem described above.
Consider the setup shown below, with a valve to adjust the flow of a fluid to an orifice meter equipped with a differential manometer across it, in series with a rotameter that has been previously calibrated for liquid acetone (density= 0.791 g/cm3), the fluid of interest. The rotameter calibration expression was found to be V=1.56R, where the volumetric flow rate is in mL/s and the rotameter reading is unitless. The manometer fluid has a specific gravity of 1.210. a) For one valve setting resulting in a rotameter reading of 82.0 as liquid acetone flows through the system, the height difference of the manometer fluid is 22.0 mm. The volumetric flow rate for this condition in mL/s with 3 sig. fig's is b) For one valve setting resulting in a rotameter reading of 80.0 as liquid acetone flows through the system, the height difference of the manometer fluid is 22.3 mm. The pressure drop for this condition in Pascals (Pa) with 3 sig. fig's is
A Pipe used to transport an oil of specific gravity of 0.90 & 0.03poise at a Velocity of 1.6977m/s with a flow rate of 3cubic meter per second. A Pipe was used to conduct a test using water at 20 degree celsius with a velocity of 5.0931m/s. Find the diameter of the prototype. Viscosity of water at 20 degree celsius is 0.01poise