4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) 1+j2 n wwwm ao |VL| = 207.85 V bo- Figure ...+j18 n

4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) 1+j2 n wwwm ao |VL| = 207.85 V bo- Figure ...+j18 n

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.29P: Consider three ideal single-phase transformers (with a voltage gain of ) put together as ...

See similar textbooks

Similar questions

The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Describe the star-delta connection configuration types in three phase transformers and their necessity by drawing and writing. Thank you very much if you answer.
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
4. An Open-Wye/Open-Delta transformer, as shown in Figure, is formed by two identical single-phase transformers. The primary line-to-line voltage is 12.47 kV, and the secondary line-to-line voltage is 208 V. Take
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3 phase side. The main transformer primary to secondary turns ratio is (12/1).
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the disadvantages? (can you explain with drawing?)
Two single-phase transformers whose phase electrical equivalent circuits are given below are connected in parallel and ZL= 0.8+j0.6 ohm is feeding a worth of load. Idle operating voltage of Transformer 1 is 220 V and Transformer 2 idle operating voltage is 240V. a.) Find the currents flowing from transformers to the load. b.) Find the active powers that transformers transfer to the load.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.