6 6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a single live load of 40 kN. Determine (a) the maximum positive moment created by these loads at E, and (b) the maximum positive shear at E. Assume A and C are rollers, and B is a short link. A - 4 m B 4 m CI 4 m Prob. 6-22 E 4 m D @Sei

6 6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a single live load of 40 kN. Determine (a) the maximum positive moment created by these loads at E, and (b) the maximum positive shear at E. Assume A and C are rollers, and B is a short link. A - 4 m B 4 m CI 4 m Prob. 6-22 E 4 m D @Sei

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Dr. A H.W.5: A rigid bar ABCD is supported by two bars, as shown in Fig- ure 3 .There is no strain in the vertical bars before load Pis applied. After load P is applied, the normal strain in rod (1) is -570 pm/m. Determine (b) the normal strain in rod (2) if there is a l-mm gap in the connection at pin C before the load is applied. (c) the normal strain in rod (2) if there is a l-mm gap in the connection at pin B before the load is applied. (a) the normal strain in rod (2). (2) 1,500 mm 360 mm 140 mm 240 mm Rigid bar bber C B 900 mm (1)
The solid 32 mm diameter steel [E - 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P- 500 N, Q- 950 N, Las - 450 mm, Lạc - 650 mm, Lco - 650 mm. A B C D LAB LBC LCD Part 1 Calculate the area moment of inertia for the solid circular cross-section. Answer: |- i mm4
the connection consists of a plate connected to another plate by five 25-mm diameter rivets. it carries a load P = 80 kN. Determine the maximum shear stress on the bolt due to the effect of moment alone
*2-16. Classify each of the structures as statically determinate, statically indeterminate, or unstable. If indeterminate, specify the degree of indeterminacy. The supports or connections are to be assumed as stated. roller pin fixed 8 bns Aanogque od tneno (a) A roller В Гoller rollerC (b) ol d no no A D pin roller B rollerC pin (c) Prob. 2-16
A solid 1.00-in.-diameter steel [G = 12000 ksi] shaft is subjected to the torques shown. Determine the rotation angle of pulley D with respect to the support at A. (1) 240 lb-ft 36 in. O-0.0653 rad O-0.0513 rad O-0.0415 rad O-0.0542 rad O-0.0316 rad B (2) 36 in. 215 lb-ft (3) 36 in. 110 lb-ft D
The compound girder shown in the figure below is subjected to a uniform live load of 12 kN/m, a uniform dead load of 4 kN/m, and a concentrated live force of 38 kN. Determine (a) the maximum reactions at supports, and (b) the maximum negative shear and moment at point D. A 20'- B hinge C 8 10'- E 10-
*3-4. The bearing consists of rollers, symmetrically confined within the housing. The bottom one is subjected to a 125-N force at its contact A due to the load on the shaft. Determine the normal reactions NB and Nc on the bearing at its contact points B and C for equilibrium. 40 B Ng- 125 N Prob. 3-4
The A-frame shown supports the 250-N load and 85-N load acting on horizontal member. It is hinged at E and rocker supported at A. Determine the pin reaction at B, C and D. Use method of members.
The rigid member is held in the position show by three steel tie rods. Each rod has an unstretched length of 0.75mm and a cross?sectional area of 125 mm2. Find the forces in the rods if the turnbuckle on rod EF undergoes one full turn. The lead of the screw is 1.75 mm (the lead of the screw would cause the rod to shorten (when unloaded) by 1.75 mm when the turnbuckle is rotated 1 revolution. Esteel: 200 GPa. USE THE FORCE METHOD TO SOLVE 0.75 m B A-0.5 m -0.5 m-C 0.75 m What is the force in member EF? What is the force in member AB? =
Find the tension in the Active tension bracing in the center bay (hint: again, there is no need to find reactions). E B O с D 16' -12'- H 8k 12' G 2k 12' F 4k 3k
CDEFGH is plate with a circular hole in it and has a unit weight p (N/m?). It is attached on DE beam with weld. A crate has a weight of W (kN) at A is linked to the plate from C by the help of a cord. The surface under the crate has a coefficient of static friction u1 and the pulley has a coeficient of static friction µ2. a) Find the center of the gravity of the CDEFGH plate according to O (given in grey color in the figure). HCD is half circle centered at O. A full circle centered at O is removed from the plate. • HOD line and EF line are vertical. В A H G 3m Ce d. F Im D E K 2m a а (m) b (m) c (m) d (m) p (N/m²) 3 2 5 1 30 0.2 0.2 200
F8-4. Determine the magnitude of the load P that will cause a maximum normal stress of max = 30 ksi in the link along section a-a. - 2 in.- E- a a 0.5 in. 2 in. T F8-4