7. (15') Stack: What is the function of the stack? If the current values in the stack segment register and stack pointer are (SS)=2CE016 and (SP)=EE3416, respectively, calculate the addresses of Bottom of Stack (BOS), Top of Stack (TOS), End of Stack (EOS). How many words of data are currently being stored in the stack?

7. (15') Stack: What is the function of the stack? If the current values in the stack segment register and stack pointer are (SS)=2CE016 and (SP)=EE3416, respectively, calculate the addresses of Bottom of Stack (BOS), Top of Stack (TOS), End of Stack (EOS). How many words of data are currently being stored in the stack?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

If the current value of the stack segment register and stack pointer are C00016 and F F0016, respectively, what is the address of the current top of the stack ?
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of the following instructions determine the resultant content of ACCA or ACCB. (a) ANDA $C100 (b) ANDA #$05 ORAB #$EE (c) (d) CLR B (e) NEGA (f) DECB (g) ASLA (h) LSRB (i) EORA #$E4 (G) ROR A
Write a program to add the following five data bytes stored in memory locations starting from XX60H, and display the sum. (The sum does not generate a carry. Use register pair DE as a memory pointer to transfer a byte from memory into a register.) Make a flow chart for the same. Data(H) 1A, 32, 4F, 12, 27
Write a Verilog code for 8-bit up/down counter for any type of Modeling.
true or false ?? an even two bit parity checker will output a parity error if data A=LOW data , B=HIGH. parity bit = HIGH
In a multibyte addition program, when must you use the ADD instruction? When must you use the ADC instruction?
7- Write an 8051 program to exchange the contents of the stack pointer SP and the flag register PSW.
1.Show the status of PSW (Program status word) after addition of two 8bit numbers 26H and 3FH. Also draw status of flag register with help of diagram? 2. Mention the addressing mode, function and how many bytes instruction for the following instructions? ADI 42H b. LXI H, 2500H c. RLC 3. Write assembly language program to add to 8-bit numbers with carry. First numbers stored on memory location 2500h, second number on 2501H and store 8bit result on memory location 2502H and carry on 2503H.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0