A nonflow system has a mass of 5 lb. in it. The system undergoes a process during which 200 ft.lbf of heat is transferred to the surroundings. If the system does 1000 ft.·lbf of work on the surroundings, determine the change in specific internal energy of the fluid in lbf/lbm.

A nonflow system has a mass of 5 lb. in it. The system undergoes a process during which 200 ft.lbf of heat is transferred to the surroundings. If the system does 1000 ft.·lbf of work on the surroundings, determine the change in specific internal energy of the fluid in lbf/lbm.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 27RQ: How many Btu/h would be produced in a 12-kW electricheater?

See similar textbooks

Related questions

Q: As shown in the figure below, a cylinder fitted with a piston is filled with 600 lb of saturated…

A: Given:-Mass of the ammonia (m) = 600 lbCondition of ammonia is saturated liquid at 15°CTo Find…

Q: 2. Determine the forces in member BC, BE and EF of the truss shown in the figure by Method of…

A: Dear student, as per the given diagram the data given is wrong. As per my knowledge, I have…

Q: A rigid, well-insulated tank contains a two-phase mixture of ammonia with 0.0025 ft of saturated…

A: The given information in the problem is listed in the following attached image:

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given Data- A plane truss given we have to find force in all member of given truss

Q: D P -2 m- -2m- B A 3 m

A: Given Data- A plane truss given we have to find Force in all member of given truss

Q: ▼ Part A If the coordinate direction angles for F3 = 730 lb are a = 100°, B = 50°, and y = 42°,…

Q: Moist air at 70 °F b and 45 % relative humidity is recirculated from a room and mixed with outdoor…

A: Given Data The temperature of the inlet air is: Tia=70°F=21.11°C The temperature of the outdoor air…

Q: Ammonia undergoes an isothermal process from an initial state at T₁ = 83°F and v₁ = = 10ft³ /lbm to…

Q: A rigid, well-insulated tank contains a two-phase mixture of ammonia with 0.0022 ft3 of saturated…

A: Given that: At state 1, volume of saturated liquid and saturated vapor are 0.0022 ft3 and 1.5 ft3…

Q: Determine the maximum allowable suction head for a pump with a cavitation constant equal to 0.3 when…

Q: A rocket, fired from rest at time t = 0, has an initial mass of m0 (including its fuel). Assuming…

Q: I C1040, OQT 1000°F, ultimate strength is approxima

A: Ultimate Strength:- The maximum resistance to fracture of a material is measured by its ultimate…

Q: Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 60%, and a volume of…

A: The given information in the problem is listed in the following attached image:

Q: Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 70%, and a volume of…

A: GivenT=300oFx=70%V=6 ft3Q˙=0.3Btu/s

Q: A structural component in the form of a wide plate is to be fabricated from a steel alloy that has a…

Q: The difference in water surface levels in two tanks, which are connected by three pipes in series of…

Q: Five lbs of propane is contained in a closed, rigid tank initially at 80 lbf/in.2, 130°F. Heat…

A: Given data: m=5 lbP1=80 lbf/in2T1=130°FT2=0°F Need to determine the amount of energy transfer by…

Q: write vector loop equation(s) theta2=57 also if a new length is constructed find its value.

Q: Air with dry bulb temperature of 25°C (Psat=3.169 kPa) and a wet bulb temperature of 15°C (Psat =…

Q: Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water.…

A: Given data Pressure = 35 psi Flow rate = 500 gpm Density of water = 62 lbs/ft^3 Find the pump head…

Q: Figure 2 shows a horizontal beam AB. It is pin-supported at end A and carrying a load Q at end B.…

A: Given data :- b = 60 mm Q= 109 kn Factor of safety = 2.0 Youngs modulus (E) = 200Gpa Find the length…

Q: Air is compressed in a piston-cylinder assembly from p₁ - 10 lb/in², T₁-500°R, V₁-9 ft³ to a final…

Q: Determine the tensions in cables AB, AC, and AD. B Answers: TAB= TAC = i i TAD = i 2.0 m C 1.35 m…

A: Given data Weight of cylinder = 140 N Find the tension in each cable.

Q: Determine the volume, in ft³, of 2 lb of a two-phase liquid-vapor mixture of Refrigerant 134A at…

Q: A refrigerator has a coefficient of performance of 1.6. How much work in KJ must be supplied to this…

Q: 5. Air at 20°C db & DPT 20°C Determine the following: a. RH (Relative Humidity) b. DPT (Due…

A: Given Data The dry bulb temperature is: DBT=20° The dew point temperature is: DPT=20° To Determine…

Q: A torque T is applied at the free end of a stepped rod of circular cross-sections as shown in the…

A: Given:To determine the expression for d to produce an angular twist θ at the free end.Torque…

Q: Design the diameter of a steel pipe to carry water having kinematic viscosity v=10 m²/s with a mean…

Q: Carnot heat engine receives heat from a reservoir at 900°C at a rate of 800 kJ/min and rejects the…

Q: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB BC BD…

A: f = friction factor = 0.020 LAB = 1200 m, dAB = 250 mm LBC = 600 m, dBC = 200 mm LBD = 800 m, dBD =…

Q: Calculate the DOF for the mechanisms below: (2) 0₂ 0₂ 0₁ 0₁ 06 06 9 X

Q: Consider a steam pipe of length L = 20 m, inner radius r₁ = 6 cm, outer radius r₂ = 12 cm, and…

Q: As a piping designer, you were tasked to determine the required water-surface elevation between the…

Q: Suppose a weight of mass 5 kg is attached to a spring with spring constant k = 5 N/m and damping…

A: Given: Mass→m=5 Kg Spring constant→k=5 N/m Damping constant→C=10 Ns/m Because natural frequency:…

Q: 9-17 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

Q: What is the internal shear force over the cross section at point C? 8 kN/m -30 kN ☐-6 kN 30 kN -62…

Q: 9-29 The permissible shear stress for the weldment illustrated is 140 MPa. Estimate the load, F,…

A: Given Dataτs=140Mpad=75mms=6mm

Q: A tank contains 7 kg of dry air and 0.1 kg of H₂o vapor at 30°C (Psat = 4.286 kPa) and 100kPa total…

A: Given Data- Mass of air ma=7kg Mass of water vapour mv=0.1kg T=30'C Psat=4.286KPa P=100KPa We have…

Q: Disposal Instruction of grinding machine

A: Grinding Machine : A grinding machine is machine which is used rough rotating abrasive wheel which…

Q: Part A The force F = (-6i+ 3j+ 14 k) N is applied to the block shown in (Eigure 1). Figure -3 m 2 D…

Q: A flywheel has its angular speed increased uniformly from 18 rad/s to 75 rad/s in 80 s. If the…

A: Given Diameter, d = 3.5 ft Angular speed = 18 rad/s to 75 rad/s Time, t = 80 sec…

Q: Consider modeling a temperature sensor as a sphere having a thermal conductivity of 91 W/m-K, a…

Q: An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is…

Q: HVAC UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. PLEASE ANSWER ALL THE SUBQUESTON…

Q: Question 2: The following water turbine generates 750 W of power when releasing water from the tank.…

A: Given data as per the question Power generated bu turbine =750 w Head =25 m

Q: A load of 200 pounds is exerted on a piston confining oil in a circular cylinder with an inside…

A: Load exerted on piston, F = 200 lb Inside diameter, d = 2.5 inches Cross sectional area of piston,…

Q: Determine the force in member BD and state whether the member is in tension or compression. Iren 30°…

A: Given Force, F = 7.8 kN Angle = 30o Find Force in member BD, RBD

Q: 4) Consider the steady two-dimensional flows with velocity fields y x² + y² and U= x x² + y²¹ V = x…

Q: A hollow circular shaft has an outer diameter of 100 mm and a wall thickness of 25 mm. The allowable…

Q: At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A certain system dissipates 250 BTU of heat to the surroundings. If the increase in internal energy is 222,000 ft-lbf, what is the work done? Is it done on or done by the system?
There is 10-kg of water at room temperature and pressure in a closed piston-cylinder. Boundary work is then done on the system, compressing it until the volume decreases to one-half of it's original value. If the internal energy of the system decreases by 700 kJ/kg during this process and 200 kJ/kg of boundary work is done on the system, how much heat has been removed from the system, in kJ. Assume that system is sitting on a lab bench.How much heat is removed from the system, in kJ?
2. A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lb/cu ft and discharges it with a density of 0.304 lbm/cu ft. At the suction, p1 = 15 psia; at discharge, p2 = 80 psia. The increase in the specific internal energy is 33.8 Btu/lbm. Determine the work on the air in Btu/min and in hp. Neglect change in kinetic energy.
Explane the Flow work is the energy needed to push a fluid into or out of a control volume, and it is equal to Pv.
Determine the work done by a kilogram of the fluid system as it expands slowly in a piston-cylinder arrangement from an initial pressure and volume of 550 kPa and 0.028 m3 respectively to a final volume of 0.113 m3in accordance with the following defining relations: a.) p = C; b.) pV = C; c.) pV1.4 = C; d.) p = -730V + 690 kpa where V is in m3
Work is done on an adiabatic system due to which its velocity changes from 10 m/s to 20 m/ s. elevation increases by 20 m and temperature increases by 1 K. The mass of the system is 10 kg. Cv= 100 J/(kg K) and gravitational acceleration is 10 m/s². If there is no change in any other component of the energy of the system, the magnitude of total work done (in kJ) on the system is
In an engineering system, air passes through two sequential processes. Process 1-2: Polytropic compression, n =1,3, P1=100 kPa, v1 =0.04 m3/kg v2 =0.02 m3/kg.Process 2-3: Constant pressure process untill v3=v1. Draw the P-V diagram of the system. Determine the work per unit air mass. (kJ/kg)
A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 lbm/cu ft and discharges it with a density of 0.304 lbm/cu ft. At the suction, p1=15 psia; at discharge, p2=80 psia. The increase in the specific internal energy is 33.8 Btu/lbm. Determine the work on the air in Btu/min and in hp. Neglect change in kinetic energy.
A mass of 7 kg undergoes a process during which velocity decreases from 32 m/s to 19m/s, while the elevation remain unchanged. The initial specific internal energy of the mass is 1.24 kJ/kg and the final specific internal energy is 2.08 kJ/kg. During the process, the mass receives 2 kJ of energy by heat transfer through its bottom surface and loses 0.8 kJ by heat transfer through its top surface. How much is the work in kJ? (hint: be consistent with units) ( 2 decimal places)
On a cold winter day, the rate of heat transfer from the air in a certain room is 5500 Btu/hr. The room is heated by a heating system, and the warm air is circulated by a fan which develops 0.75 hp. What is the required rate of heat transfer in kW, from the heating system in order to maintain constant room conditions?
Determine the Kinetic energy in BTU of a 8 lbm block moving at a velocity of 85 ft/s.
A gas is compressed from an initial volume of 5.75 LL to a final volume of 1.24 LL by an external pressure of 1.00 barbar . During the compression, the gas releases 125 JJ of heat. What is the change in internal energy of the gas?