Consider the water distribution network. Given the information below, find the flow rate between A and В. A pipe has an absolute roughness of 0.0008 ft. 1.5 MGD of 50 deg F water (kinematic viscosity is 1.410 x 10-5 ft2/s) enters at junction A and leaves at junction B. The acceptable pressure at point D is 40 psig (280 kPa).

Consider the water distribution network. Given the information below, find the flow rate between A and В. A pipe has an absolute roughness of 0.0008 ft. 1.5 MGD of 50 deg F water (kinematic viscosity is 1.410 x 10-5 ft2/s) enters at junction A and leaves at junction B. The acceptable pressure at point D is 40 psig (280 kPa).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 10-5 ft2/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s². Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. 2 Drag and Drop your answer below. A BI 三三EE II 125 !! ...
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
A pipe carries a flow of 5.17 cfs of oil (SG = 0.877). At one location where the diameter is 6 inch, the pressure is 13. 2 psi. At another location which is 12 ft higher in elevation, the diameter is 18 inch and the pressure is 8.75 psi. Determine the head loss between the two locations, and the direction of flow.
In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 105 ft?/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s?. Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. (1) A B
Problem 3 The pipes shown in the system are all concrete. With a flow of 25 ft³/s (or cfs) of water, find the head loss (hL, AB) and the division of flow in the pipes (Q1, Q2, and Q3) from A to B. Assume: 1) f = 0.030 for all pipes; 2) all the minor head losses in the system are negligible. Assume α = 1.0 throughout. A L= 3000 ft D = 14 in. L = 2000 ft D = 24 in. L = 2000 ft L= 3000 ft D = 30 in. D = 12 in. B L= 3000 ft D= 16 in.
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
The discharge from A to B is 50L/s. Pipe 1 is 650m long and 0.3m in diameter. Pipe2 is 500m long and 0.5m in diameter. Pipe 3 is 750m long and 0.4m in diameter. The surface roughnessin all pipes is 0.36mm. Assume that the kinematic viscosity of water is 1x10-6 m 2 /s. Determine the headloss from A to B. Solve using either the method of equivalent pipes or the Hardy Cross Method.
A 300mm diameter pipe has a flow rate of 200 L/s. Assuming the length of the pipe is 300mm, and the head loss is 10m, determine a) friction factor, b) roughness coefficient, and c) Hazen Williams Coefficient A) f = 0.0236 В n 0.0412 No answer among the choices in C question C D) C = 93.43 E n = 0.0348 F C = 87.96 G) f= 0.0245 H) C = 101.09 No answer among the choices in question B () J n = 0.0115 %3D K f = 0.0218 L n = 0.0243 M) f= 0.0257 N. C = 107.57 No answer among the choices in question A
2.Water (ρ = 1000kg / m3, μ = 10-3Pa.s) flows at a speed of 1.6m / s (Reynolds number Re = 0.8 105) in a pipe whose diameter is to be determined.
Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm-100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?). 5 m
Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipe diameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.