Degree of drawing is measured in terms of; Reduction in strain Reduction in area O Reduction in force O Reduction in stress In a hot chamber die casting machine; Nonferrous alloys with low Tm are casted O Ferrous alloys with high Tm are casted Nonferrous alloys with high Tm are casted Ferrous alloys with low Tm are casted

Degree of drawing is measured in terms of; Reduction in strain Reduction in area O Reduction in force O Reduction in stress In a hot chamber die casting machine; Nonferrous alloys with low Tm are casted O Ferrous alloys with high Tm are casted Nonferrous alloys with high Tm are casted Ferrous alloys with low Tm are casted

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.7: Heat Treatment Of Metals

Problem 2RQ: Direct hardening can be performed on steel containing at least________ carbon.

See similar textbooks

Similar questions

Direct hardening can be performed on steel containing at least________ carbon.
Pick the best soultion for the multiple choices. Modulus of resilience is: Slope of elastic portion of stress – strain curve Area under the elastic portion of the stress –strain curve Energy absorbed during fracture in a tension test Energy absorbed during fracture in an impact test Slope of the plastic portion of the stress- strain curve ( ) Fatigue failure occurs under the condition of: High elastic stress High corrosivity High stress fluctuations High temperature High rate of loading ( ) Creep failure of a material occurs most rapidly when the operating temperature is: Cryogenic temperature Equal to its melting point Grater than 0.4 times its melting point in K Greater than 200 oF Close to boiling point ( ) Young’s modulus of a material is indicative of its: Tensile strength Yield Strength Ductility Stiffness Corrosion Resistance…
Q3] A. What are annealing purposes? B. Calculate the upper and lower critical temperature for steel composition as follow: %C %Si %Mn %P %S %Cr %Mo %Fe 0.15 1.00 0.60 0.025 0.025 9. 1.10 balance
Q3/ A-Define the following: Duplex stainless steel , Super alloy , Martinsite, Muntiz metal, Flam hardening ,Twinning. B- What's meaning by critical resolved shear stress?
Both for Ferritic and Martimenistic sstainless steel belong to the AISI 400 series. Farris stainless steel's are heat treatable grades and Martinisitic stick stainless steel's can only be strain hearted to improve their mechanical properties. True or false
36 Asiacell O Homework 4 -... -> 3 Class Materials Eng. Dep. Heat Treatment Ismail Ibrahim Marhoon Homework 4 Q1: 1.5 in diameter steel part is quenched in oil with no agitation. (H=0.20). If we use a 4340; 4140; 8640; 5140; 1040 steel, what would be the hardness number at the center of the part? Q2: Determine the best quenching medium to produce a minimum hardness of HRC 40 at the center of a 3.75 cm diameter 4320 steel bar. Given Cingrate t 00c00 143 to 4340 50 40 8640 ab 9310 30 4320 1050 1040 10 20 it 1 1 2n 10 20 30 Jominy distance th of an inch) Die he eted e TABLE The N canticient, or seveity of the querch, far several guenehing sedla H Coefticient Coaling Rate at he Center of a l-in. Bar (CA) Medium Ol no taton) 04 anitation) 025 18 45 HyD inc agtation H0 fegiutont Brine Ino agtaton) Brine lapttiori 10 4.0 190 20 60 90 230 Ad DISTANCE FROM OUENCHED END IN) DIAMETER IN)
Q4/ . B- State the purpose of case hardening of steel?
Identify the mold die material in order to produce the steel casting parts. Steel Cast iron Graphite Wood Full annealing can be done at lower temperature than the subcritical annealing. Select one: True False
The Sheady Ceap data of stainless cheel tkon at Stress level Fompa ů qiven in te Table Compute he steady-ctate Cleep dets for this alloy at 1a5ok and Shee level of 5omPaf Hhe shees erpinen t fox the alloy ū 7.0. fempersiuse 977 1089 2.0X 183
To get rid of the total residual stress in steel_ heat treatment process is most suitable. Tempering Normalizing Martempering O Annealing
Q4: Answer with True or False: 1-Cooling rate when quenching steel in agitated water is faster than brine. 2-Normalizing can be done for hypereutectoid steels by heating the steel above Acm. 3-Marquenching of the hardened steel sometimes causes quench cracks. 4-New carbides type begins to form after tempering AISI 1020 steel after 100°C. 5-Recrystallization temperature decreases with increasing the percentage of prior cold work. 6-Steels are categorized depending on their microstructure and how they've been heat treated. 7-Annihilation of dislocations, polygonization is commercially done by recrystallization annealing 8-Process annealing for cold worked for AISI 1040 steel includes heating the steel to 650°C. 9-Carbon content increases martensite start and finish temperatures. 10-Retained austenite is more at center than surface of a quenched part.
Steel is most suited for cold chamber pressure die casting process. Select one: True False