h) Determine the flow type in 5 selected pipelines and explain how the pipe flow classificationaffects the design procedure of your network.i) Knowing that the excess water will be discharged at 100 m long pipeline made of galvanizediron and a slope of 0.2%. Compare and assess the designed pipe using both Hazen Williamsand Darcy Weisbach by stating the similarities and differences in each different hydrodynamicapproach. What would be the most efficient approach from your point of view?

Types of fluid flow in a pipe steady or unsteady compressible or incompressible viscous or…

Answered: Determine the flow type in 5 selected…

Determine the flow type in 5 selected pipelines and explain how the pipe flow classification ffects the design procedure of your network.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
(a) Suppose we have planned to design a hydraulic system.ln this aspect, the pump selection is to be finalized for a flow rate of 3907 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.4 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. (b) Write the significance of using minimum diameter pipelines in the hydraulic system. (a) Area of the maximum sized pipe diameter (in m?) (b) Area of the minimum sized pipe diameter (in m2) (c) The minimum sized pipe diameter (in m) (d) The maximum sized pipe diameter (in m)
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and loss coefficient of each pipe are given below. For p= 62.4 Ibm/ft and u = 0.7E–3 lbm ft/s find total pressure drop and the diameter of an equivalent pipe representing this system. C) Fluid Power Theory an.. IndPitEn IlIb. Fluid Mechanics: Incompressible Viscous Flow 392 Pipe D K No. (ft) 100.00 (in) 5.00 (-) 50.00 1 2 80.00 4.50 45.00 3 70.00 4.00 65.00 4 120.00 3.50 55.00 5 90.00 3.00 15.00
write legibly Complex Pipeline System_Series Pipes 1. Three new cast-iron pipes were connected in series: pipe 1, 12 in. diameter and 1200 ft long; pipe 2, 24 in. diameter and 2000 ft long; and pipe 3, 18 in. diameter and 1500 ft long. If the total flow in the system is 8.0 cfs, determine the (a) total lost head, ft; and(b) the equivalent length of a 20 in. diameter pipe. Use a C value of 120 for all pipes. (a) total lost head : _______________________ ft(b) equivalent length : _______________________ ft
CS) Flow through a heat exchanger tube is to be studied by means of a 1/10 scale model. If the tmateaangeraarmall, carries widecreme de ratio of pressure losses between the model and the prototype if water is used in the model.
On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
Medium oil with kinematic viscosity 6.10 x 10^-6 m^2/s, flows through a strsight pipe at a rate of 6.0 liters/s. For laminar flow comditions, what is the least diameter of the pipe. Provide FBD and choose teh correct answer below: a. 60 cm b. 62 cm c. 64 cm d. 66 cm
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.. A cylindrical tank 5 ft high has a constant diameter of 4 ft is full of water. The tank has a hole2. A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a holein its bo]om that measures 0.1ft^2. All losses are insignificant. How long will it take for the tankto empty? Note that you can NOT assume a staLc head and constant flow rate because thewater head in the tank decreases as the water flows out of the tank (A) 35 sec(B) 70 sec(C) 105 sec(D) 140 sec
Medium oil with kinematic viscosity 6.10 x 10^-6 m^2/s, flows through a strsight pipe at a rate of 6.0 liters/s. For laminar flow comditions, what is the least diameter of the pipe. Choices: a.62 cm b.60 cm c.64 cm d.66 cm
As a process engineer, you are designing a new drinking water treatment plant using conventional treatment process including Two Rapid Mixers as follows: The design flow is 50 million gallons per day (MGD) (1 Gallon = 3.785 L, 1 m³ = 1000 L). The average temperature of water is 5°C with a dynamic viscosity, μ = 1.519 x 10-3 Pa.Sec In each rapid mixer with a square shape, detention time, e = 1 min, water depth H = 13 ft, and power input P = 1.5 kw (1 ft = 0.3048 m, 1 KW = 1,000 W) The equivalent diameter, TE for each rapid mixer is ________ m. TE || AIR 1) 4.1 2) 4.4 3) 4.6 4) 4.8 5) 0.4
Q.3 b) A total of 14 litres per second of oil is pumped through two pipes in parallel, one 12 cm in diameter and the other 8 cm in diameter, both pipes being 1200 metres long. The specific gravity of the oil is 0.97 and the kinematic viscosity 9 cm^2 per second. Calculate the flowrate through each pipe and the power of the pump. ,