Determine the shear and moment diagrams for the loaded cantilever beam. Then answer the questions. The distance xis measured from point A to the right. 550 N/m A 2.0 m 3.2 m Questions: At x = 0.2 m, V = i N, M = i N-m At x = 2.5 m, V= i N, M = i N-m The maximum (absolute value) shear force is i The maximum (absolute value) bending moment is i N-m

Determine the shear and moment diagrams for the loaded cantilever beam. Then answer the questions. The distance xis measured from point A to the right. 550 N/m A 2.0 m 3.2 m Questions: At x = 0.2 m, V = i N, M = i N-m At x = 2.5 m, V= i N, M = i N-m The maximum (absolute value) shear force is i The maximum (absolute value) bending moment is i N-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
Problem #2 A wood beam with a square cross section supports the load as shown. Determine the cross sectional dimension in millimeter if the allowable flexure stress is 1000 KPa. Use double integration method. Note: Maximum moment occur at support. 100N/m 100N 1m 4
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
Compute the vertical displacement (downward) at Joint C of the given truss shown in Figure 2 using the method of virtual work. You can use Space Gass to compute the internal forces of the real and virtual systems without manual calculations. Assume the cross-sectional area and modulus of elasticity of each member are constant. F B H 3 kN + G 4 kN + D 3 kN + + 3 m
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point E. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point E. Express your answer in kilopounds to three significant figures. c) Determine the moment at point E. Express your answer in kilopound-feet to three significant figures.
1) A simple supported beam is subjected to a 10 kN/m uniform distributed load over the 6m distance of A support. At the the B support there is a 40 kN.m moment. Using the double integration method; a) Draw the elastic curve of the cantilever beam b) Determine the slope and deflection at the point where the moment is maximum. c) Determine the slope and deflection at the point where the shear force equal to 12,5 kN. MIHA The 10 kN/m 6 m 2 m 40 kN/m
From the given simply supported beam below, determine the following: a, The shear and moment equation of each segment of the beami Use point A as reference of b. The Shear and Mament Diagram of the beam e The maximum shearand moment of the beam. d. The moment of Ihertia with respect to the neutral axls. e. The maximum flexurál stress and shear stress of the beam. I. The bending stress at point B andC * The shear stressät the mid-point of the beam. 20 kN 14 kN / m 10 KN / m A B [D] E 4 m 25 m 25 m 3 m 360 mm 80 mm 130 mm 130 mm 300 mm 90 mm 280 mm
Draw the shear force and bending moment diagrams of the beam whose span and loading condition are given in the figure. Calculate the section rotation (OA) at point A and the vertical displacement (Yc) at point C using the moment are theorem in mm. (EI = 50000 kN.m2) P=3kN L1=4m L2=1.3m A EI L1 (m) B * 2EI L2 (m) C P (KN)
4: The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque To that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. 0.60 in. H 5.0 in. To 1.30 in. 14.5 in
4. A rigid beam fixed at O is loaded by an nth degree spandrel having a vertex at B. a. Determine the shear functions. Use the fixed end as the origin and set rightward and upward as positive directions. Express your answers as V(x)={shear expression} without simplifying {shear expression}. Show all FBDS used b. Draw the shear diagram c. Draw the moment diagram d. If the magnitude of the maximum moment is 20.25kNm, determine the degree of n. 3m 3m A B +x kN 5 no m
Q2. Calculate the deflection at point D for the following static beam structure using the Unit Load and Moment Area method P = a kN D q = a +b B EI b/4 m b/2 m b Where: E3D 210 х 106 I= 8360 x 10-8 a = 3 b = 2a 3 b b A = (2/3) A = (1/3)