INSTRUCTIONS: (1) Analyze the shown indeterminate beam by the slope deflection method. Be guided as follows: a. Determine the degree of kinematic indeterminacy. b. Compute the fixed end moments. c. Construct the modified slope deflection equations. d. Construct the joint equilibrium equations. e. Compute the unknown rotations (0/EI). f. Compute the member end moments g. Compute reactions at supports h. Draw shear and moment diagrams EI 2EI EI Members AB, BC, CD have the same length L = 5 m Flexural rigidities are El, 2EI, El respectively. Concentrated load of magnitude P = 5 KN acts at a distance a = 1 m from the support A. Uniform load of intensity q = 5 KN/m acts on BC. Member CD is loaded at its midspan with a concentrated load of magnitude P = 5 KN

INSTRUCTIONS: (1) Analyze the shown indeterminate beam by the slope deflection method. Be guided as follows: a. Determine the degree of kinematic indeterminacy. b. Compute the fixed end moments. c. Construct the modified slope deflection equations. d. Construct the joint equilibrium equations. e. Compute the unknown rotations (0/EI). f. Compute the member end moments g. Compute reactions at supports h. Draw shear and moment diagrams EI 2EI EI Members AB, BC, CD have the same length L = 5 m Flexural rigidities are El, 2EI, El respectively. Concentrated load of magnitude P = 5 KN acts at a distance a = 1 m from the support A. Uniform load of intensity q = 5 KN/m acts on BC. Member CD is loaded at its midspan with a concentrated load of magnitude P = 5 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam is free of support at point A and is clamped at the point B, as shown in the Figure Q4 below. Calculate the support reaction force and moment for the non-uniformly distributed load, where w =74 N/m and L = 6 m. The downward direction is denoted as positive direction in force and the anti- clockwise direction is defined as positve in moment. For all numerical answers, answer to within 3 decimal places. A v y -L- Figure Q4: A cantilever beam under non-uniformly distributed load
For the beam shown, how does the shear change as you move from A to B? L- Select the correct response: There is not enough information to tell. It stays constant. It decreases linearly. It increases linearly
SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem IV. Determine the support reactions of the beam shown. El is constant for the entire beam. 20kN/m A 4m B 4m 40kN/m -X
Determine the support reaction at D using Conjugate Beam Method. Indicate the negative sign if the answer is downward.
Solve for the reactions on the given beam below using Slope Deflection Method
INSTRUCTIONS: (1) Analyze the shown indeterminate beam by the slope deflection method. Be guided as follows: a. Determine the degree of kinematic indeterminacy. b. Compute the fixed end moments. c. Construct the modified slope deflection equations. d. Construct the joint equilibrium equations. e. Compute the unknown rotations (0/EI). f. Compute the member end moments g. Compute reactions at supports h. Draw shear and moment diagrams P. EI 2EI EI b. Members AB, BC, CD have the same length L = 5 m Flexural rigidities are El, 2EI, El respectively. Concentrated load of magnitude P = 5 KN acts at a distance a = 1 m from the support A. Uniform load of intensity q = 5 KN/m acts on BC. Member CD is loaded at its midspan with a concentrated load of magnitude P = 5 KN
The beam is supported by a roller at B and a pin at C and is subjected to the distributed load shown with intensity w = 180 N/m. The maximum positive and negative internal bending moments are critical factors in the design of the beam material and geometry. Determine the largest positive and negative internal bending moments that occur in the beam and the points along the length where each occurs. Take z = 0 to be at point A at the left edge of the beam. cc 1❀0 BY NC SA 2016 Eric Davishahl a X b -a- 4.00 m 5.20 m B Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value The maximum negative internal bending moment is and occurs at z =| m to the right of A. The maximum positive internal bending moment is and occurs at x = W m to the right of A. ·b- N-m N-m
10 ft 10 ft Problem # 1 B 8k ft 10 ft Use the Virtual Work as the displacement method. Determine the reactions at Deflection Curves of Actual, Primary and Structure with Redundant Cy. the supports if the support at C is forced upwards 0.15in. Take E = 29000ksi Bkjt %3D and = 600 in^4. Note: Use Cy as the redundant reaction. Use Compatibility Equation: (+1) 0.15 = -Ac + GScc
A two-span continuous beam is loaded with a concentrated force at point C and a uniformly distributed load at span AB. The support at point A settles 12 mm. Young's modulus is E = 200 GPa, and the moment of inertia of the beam is I = 500x106 mm 4. (1) Prove that the beam is statically indeterminate to 1st degree. (2) Use the Force Method to determine support reactions at A, B and D. (3) Draw the shear force and bending moment diagrams for the beam. 12 mm settlement 3 kN/m OB 2m 4 kN 2m
Problem III. From the given fixed beam at both ends, solve the following questions using constant EI. a. Reactions at A b. Reactions at B c. Slope at 6m from B in radians d. Displacement at 4m from A in mm 4kN/m 4m -6m 12kN/m
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
Problem 2. Consider the frame shown below. Take E constant for all three members, and ignore axial deformations. a) b) Find all reactions. Draw the BMD; identify the magnitude and location of all minima, maxima, and inflection points. Find the horizontal deflection at joint C as a function of EI. 10 m XB 15 m I 21 15 m D I -30 kN