The internal loadings at a cross section through the 7.6-in.- diameter drive shaft of a turbine in (Figure 1) consist of an axial force of 2500 lb, a bending moment of 800 lb-ft, and a torsional moment of 1500 lb. ft. Figure < 1 of 1 > Part A Determine the maximum principal stress at point A. Express your answer in pounds per square inch to three significant figures. 01 = Submit Part B 02 = Submit VAΣo vec Part C Request Answer Determine the minimum principal stress at point A. Express your answer in pounds per square inch to three significant figures. VAΣ vec 6 Request Answer Tmax in-plane ? = VAΣo↓ vec psi ? Calculate the maximum in-plane shear stress at point A. Express your answer in pounds per square inch to three significant figures. psi ? psi Figure 800 lb-ft B 2500 lb 1 of 1 1500 lb-ft

The internal loadings at a cross section through the 7.6-in.- diameter drive shaft of a turbine in (Figure 1) consist of an axial force of 2500 lb, a bending moment of 800 lb-ft, and a torsional moment of 1500 lb. ft. Figure < 1 of 1 > Part A Determine the maximum principal stress at point A. Express your answer in pounds per square inch to three significant figures. 01 = Submit Part B 02 = Submit VAΣo vec Part C Request Answer Determine the minimum principal stress at point A. Express your answer in pounds per square inch to three significant figures. VAΣ vec 6 Request Answer Tmax in-plane ? = VAΣo↓ vec psi ? Calculate the maximum in-plane shear stress at point A. Express your answer in pounds per square inch to three significant figures. psi ? psi Figure 800 lb-ft B 2500 lb 1 of 1 1500 lb-ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= Consider a hollow circular shaft of inner radius r; = 1.25 inch and outer radius of ro 1.50in, subjected to the following loads Fx = 100 lb, Fy = 150 lb, and F = 100 lb. Determine the state of stress (3x3 matrix) and the principal stresses at point p. Report your answers in psi to one decimal place. Note the figure is not to scale. у P fixed support R1-25 in 90⁰ X 90⁰ R2=50 in h=20 in Fy Note the hollow circular shaft lies in the x-y plane only Fz Fx ro ri || = /1.50" 1.25" YZ cross-section р X
The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If the shaft transmits 133 kW, what is the maximum shear stress in the shaft in MPa? Round up final answer to whole number
A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque The answer is 100mm and 50 mm. can you help me this calculation and i give the answer already. and write with pen. tqvm
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
The bearings at A and B exert only x and z components of force on the steel shaft. a) Draw shear, moment and torque diagrams displaying values at each section of interest (A, B and Gear points). b) Determine the shaft's diameter to the nearest integer millimeter (Roundup) so that it can resist the loadings of the gears without exceeding an allowable shear stress Tall- Fx A 75 mm 50 mm 150 mm 350 mm B F, 250 mm Fx=15KN,Fz=22.5kN,allowable shear stress=90MPA
A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. the answers is:100mm;50mm can you help me please.. write it with hand writing this calculation Thanks.
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 345.6 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: MPa. Calculate your answer to 1 decimal place. 40 mm 30 mm T
5) Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value of all shafts is same (50 mm) and material is steel (G-85 GPa) Dimensions in mm 40 500 Nm
Determine the maximum shear stress and maximum normal stress of the cantilever shafts in the figures below: B Fle 10 KN 200 Tr 15 KN.m 20 0 Note: All dimensions in mm. OVERBY 2 Color ! S 70
Topic: Torsion The shaft is attached to rigid fixed supports at each end. The maximum shear stress will be equal in both segments when the torque T is applied at B. Determine the diameter of AB (d??). Use the given sign convention for uniformity. 2 decimal places
Question 1 A hollow steel shaft shown in Figure. Find the lengths of the two portions if the angle of twist produced in the two portions of the shaft are equal and the shear stress is not to exceed 60 MPa. (hint: use max torque) * 40 15 25 k 800 mm 1 Add file This is a required question
A shaft is subjected to a torque of 28 kNm and a maximum bending moment of 25 kNm. The shaft is solid with a diameter of 125 mm. Using the Mohr circle method find the values for the principal stresses and themaximum shear stresses on the shaft i)Construct the Mohr circle on the graph paper provided. ii) Using the Mohr circle method find the values for the principal stresses and the maximum shear stresses on the shaft.iii) Show the orientations of the planes on which the principal stresses act on a rotatedelement