und beam is subjected to a uniform dead load of and a uniform live load of 285 lb/ft. Assume B is a pin roller. Follow the sign convention. (Eigure 1) - 5 ft B 5 ft D 5 ft 1 of 1 > C Part A Determine the negative bending moment at A with the maximum magnitude. Express your answer using three significant figures. (MA)max(-) = Submit Part B ΨΠ ΑΣΦ Request Answer (VD) max(+)= ↓↑ Determine the maximum positive shear at D. Express your answer using three significant figures. —— ΑΣΦ Submit Request Answer vec vec ? ? k.ft lb

und beam is subjected to a uniform dead load of and a uniform live load of 285 lb/ft. Assume B is a pin roller. Follow the sign convention. (Eigure 1) - 5 ft B 5 ft D 5 ft 1 of 1 > C Part A Determine the negative bending moment at A with the maximum magnitude. Express your answer using three significant figures. (MA)max(-) = Submit Part B ΨΠ ΑΣΦ Request Answer (VD) max(+)= ↓↑ Determine the maximum positive shear at D. Express your answer using three significant figures. —— ΑΣΦ Submit Request Answer vec vec ? ? k.ft lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D 3 ft 2 ft 0.5 in. 1 in. T 50 Ib-ft
25 mm An eccentric force P is applied as shown to a steel bar of 25 x 90-mm cross section. The strains at A and B have been 30 mm measured and found to be A 84 = +350 u 8z = -70 u 90 mm B 45 mm Knowing that E = 200 GPa, determine (a) the distance d, (b) the magnitude of the force P. 15 mm
A beam having a tee-shaped cross section is subjected to equal (12 kN.m) bending moments, as shown in Figure. The centroid location (y-) is (110 mm) measured upward from bottom edge of stem, the moment of inertia about the z axis, is (Iz 18646000 mm4).Determine the maximum bending stress produced in the cross section. State whether the normal stress is tension (T) or compression * .(C) 100 mm 25 mm 12 kN-m 175 mm 150 mm 12 kN-m 25 mm 70.8 MPa (T) O 75.8 MPа (С С 45.0 MPa (T) O 30.8 МPа (С) О
An 85pound force is applied to the bent plate as shown. a. Take the moment about the center point between A and B. b. Change the moment into a force couple that acts through A and B.
The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle Ө0 = 0.75° when the load is applied, as shown in the detail. E = 72 GPa and I = 120 x 106mm4. Determine the following: Reaction at A (kN) Moment at B (kN m) Slope at A in radians Displacement at the application of 200kN load
Below is a truss created with 3 rod elements. Fixed at point A, sliding support at point Chas. At point B, the load P acts on the system as shown. All 3 elements have the same cross-section and are rectangular.section dimensions are given in the figure. If the safety factor used in the design is 2.5, the buckling stability should be taken into account.Calculate the highest value of the load P. E = 20 GPa
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr = 5600 Ksi. 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft ث إضافة ملف
3) Obtain the maximum bending moment Mx that the cross section given below can safely carry. The maximum normal stress is osafety = 100 MPa. T0 mm 100 mm 10 mm 20 mm 60 mm 20 mm
Determine the maximum shear stress and angle of twist (in degrees) of one tip with respect to other. The material of the component has a modulus of rigidity of 24 GPa. positive applied moments are CW when seen from E to A. Moment at A= 400 N.m Moment at B = -600 N.m Moment at C= 300 N.m Moment at D = 500 N.m Moment at E= -600 N.m L is 0.25m and Radius of the rod is 30mm
The frame shown is supported by fixed support at E and smooth surface at A. Find: • the internal forces exerted by the internal Pin at B. Bx=... By=.. • The internal force at D 600 N 0.4 m B 0.4 m A E -0.3 m- -0.3 m- -0.3 m 3 m- -0.3 m-
Determine the force in members FG, BF, and CE of the truss shown in the figure below. Let P = 29 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30° 600 60° 60 60° 30 B. 3P 4m 4m 4m Solve the force in member FG. Solve the force in member BF. Solve the force in member CE. Q =' 21 II
A force-couple system is acting on the frame as shown. Use A=80N, B=700N, C=150N, and M= 120N.m. The system is to be replaced with a single resultant force R. B 30° [Select] [Select] [Select] [Select] [Select] [Select] M 400 mm 200 mm 300 mm (a) Calculate the absolute value of the x-component of the resultant in N. (b) Calculate the absolute value of the y-component of the resultant in N. (c) Calculate the magnitude of resultant in N. (d) Calculate the angle that the resultant makes with the horizontal in degrees. (e) Calculate the absolute value of the x-intercept of the resultant's line of action in mm. (f) Calculate the absolute value of the y-intercept of the resultant's line of action in mm.