With a readable handwriting, pls solve completely and explanatory Question 3 Question 3You wish to increase the capacity of an ammeterto measure 4A instead of its quarter scaledeflection of 0.5mA. If the internal resistance ofthe permanent magnet moving coil meter is 40Ohms.a. Draw the circuit diagram to show what is neededto achieve this purpose?b. Calculate the value of the resistance that isneeded.c. Calculate the voltage of the meter

To increase the range of Ammeter, we have to connect a shunt resistance (Rsh) which is resistance…

Answered: With a readable handwriting, pls solve…

Engineering

Electrical Engineering

With a readable handwriting, pls solve completely and explanatory Question 3

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 17SQ

See similar textbooks

Similar questions

The 'skin effecť is a phenomenon experienced when current flows through a metal. Which two of the following statements are correct? 15 Select one or more: O a. A smaller 'skin depth' implies a higher resistance O b. Direct current can cause the skin effect O c. The skin depth is smaller in highly conductive metals O d. The skin depth is larger in metals with high magnetic permeability
What are the two necessary conditions for a thyristor to begin conduction?and Once a thyristor begins to conduct, what condition(s) is necessary to cease conduction? Also, why is the conduction angle greater with an inductive load than with a purely resistive load?
b. A piece of pencil lead is connected in series with an ammeter and a power supply. The power supply is turned on. After a few minutes, although the potential difference across the pencil lead does not change, the current in the circuit increases significantly. Explain why the current increases. c. Electric fields are caused by both point charges and by parallel plates with a potential difference across them. Describe the difference between the electric field caused by a point charge and the electric field between parallel plates. Your answer should include a diagram of each type of field and reference to electric field strength. Question 2
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a) Exciting current (ii) Ic (b) Magnetizing Current (iii) Ie (c) core loss current
0.1 Give a short answer for only Six of the following 1. Explain the construction of turbine meter and mention for what we use it. 2. Mention the Applications of Pyroelectric sensors. 3. Explain briefly Hall effect sensor's application by measuring the fluid level in a container. 4. Explain how could we use potentiometer to measure linear displacement and angular displacement. 5. According to electrical circuits and electric fundamentals what's the evident difference between Eddy current proximity sensor and Inductive proximity sensor? 6. What's the purpose of putting an inner track with only one hole in optical sensor? 7. What's the reason behind using Wheatstone bridge with strain gauge sensor?
Look carefully at the figure and answer the following questions. For your answers choose between on the right, on the left and it is zero; there are no more options. Clearly explain your answers. A) When the switch is closed i. Where does the current flow in the battery? ii. Where is the magnetic flux going in the bar on the left? iii. Where is the magnetic flux going in the bar on the right? iv. Towards where the current flows in the resistor?
In the figure below you see the sketches for the front and back of an electrical circuit board. The board is cut into a trapezoidal shape and is made of plastic. On the back of the board there is conductive paint shown here in green. On the front there are some resistors and capacitors, in addition to terminals for inserting the leads from a DC power supply. The legs of the resistors and capacitors go through the holes on the board and are soldered to the conducting paint on the back side. You also have a multi-meter which you can use as an ammeter or a voltmeter. 16 v 4700 16 10 8 O- 7 3. 6. 4 O+
(3) Please don't write on a paper. I can't understand handwritten. 3. HOW MANY NUMBERS OF TURNS PER METER SHOULD BE THERE FOR THE INNER COIL WITH AN AMPERE RATING OF 6A TO CANCEL THE MAGNETIC FIELD STRENGTH OF THE OUTER COIL THAT HAS 35 TURNS PER CENTIMETER AND A CURRENT RATING OF BA?
Post Test Choose the letter of the correct answer. Write the chosen letter on a separate sheet of paper. 1. It is a smail component that lights up when current flows through it. a. Capacitor 2. It regulates the amount of current flowing in an electronic circuit. a. Capacitor 3. These are devices or components which do not require an external source to their operation. b. Fuse c. LED d. Resistor b IC c. Inductors d. Resistor c. passive devices d. electrical devices a. active devices b. electronic components 4. It is a three-terminal active component that is used mainly in boosting or amplifying electrical signals; both AF and RF ranges. a. Capacitor 5. it is necessary to turn the electrical circuit "on" or "off" a. Fuse 6. Testing tools that are capable of executing tests, reporting outcomes, and comparing results with earlier test runs a. Automated 7. The testing method that starts a soon as code is written and continues in successive stages as code is combined with other units of…
What does a compatible charge mean? What if the load is not compatible?
A piezo-electrical crystal generates voltage when subjected to --- force. O a. Electrical O b. Mechanical O c. Gravity O d. All the three answers