You test a concrete cylinder having a diameter of 6.00 in and a gauge length of 12 in by applying compression forces. The results of your test are reported in the table as load vs. contraction. Draw, by hand on engineering paper, a stress-strain diagram using scales of: 1 in. = 0.5 ksi 0.2 x 103 in. in. lin. From the diagram, determine approximately the Modulus of Elasticity.

You test a concrete cylinder having a diameter of 6.00 in and a gauge length of 12 in by applying compression forces. The results of your test are reported in the table as load vs. contraction. Draw, by hand on engineering paper, a stress-strain diagram using scales of: 1 in. = 0.5 ksi 0.2 x 103 in. in. lin. From the diagram, determine approximately the Modulus of Elasticity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-A round member having a diameter of 3cm experience an axial load of 10KN. Two strain gauges are mounted on the member, one measuring an axial strain of 600 micro-strain and the other measuring a lateral strain of -163 micro-strain. The modulus of elasticity in GPa is Choose... The Poisson ratio is Choose... + The stress in MPa is Choose... + Next page
The following data are taken from a 20mm in diameter bar of length 250mm, the following results were recorded. Assume that the curve of the stress-strain diagram is linear from the origin to the first point. P (load in kN) 8(elongation in mm) 112 0.2 154 0.3 167 0.4 0.5 174 181 0.8 Determine the a. Stress at 187 kN load in MPa b. Strain at 167 kN load in mm/mm (expressed in scientific notation) c. Modulus of elasticity in MPa d. Modulus of resilience in N-mm/mm e. Modulus of toughness in N-mm/mm 234 oo OOO O0
The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter test specimen of magnesium. After fracture, the gage length is 2.245 inch and the diameter is 0.466 inch. a). Calculate the engineering stress and strain values to fill in the blank boxes and plot the data. Load(lb) Gage Length (in) Stress (kpsi) Strain 0 2 1000 2.00154 2000 2.00308 3000 2.00462 4000 2.00615 5000 2.00769 5500 2.014 6000 2.05 6200 (max) 2.13 6000 (fracture) 2.255 b). Calculate the modulus of elasticity c). If another identical sample of the same material is pulled only to 6000 pounds and is unloaded from there, determine the gage length of the sample after unloading.
When a bar of 22 mm diameter is subjected to an axial pull of 60 kN the extension on the 49 mm gauge length is 0.1 mm and there is a decrease in diameter of 0.013 mm. Calculate the Young's Modulus. Provide your answer in GN/m2 to the nearest whole number.
The data illustrated below have been determined while the tension test of the stainless steel sample by amateur engineers. The gage length of the stainless steel sample was 50.8 mm (2.0in.) and, the original diameter of the steel sample was 12.8 mm (0.505in.). Load (Ib) Elongation (in.) Load (Ib) Elongation (in.) 14000 0.020 2 310 0.0022 14400 0.025 4 640 0.0044 14 500 0.060 6950 0.0066 14600 0.080 9 290 0.0088 14800 0.100 11 600 0.0110 14 600 0.120 13000 0.0150 13600 Fracture With the help of Excel, plot the stress-strain diagram for this test conducted, and define the following mechanical properties: a) Young modulus; b) Proportional limit; c) Yield stress @0.2% offset; d) ultimate stress; e) nominal rupture stress.
How do you dervive Hooke's law for the stress and strain components? This question pretains to the error in a measurement due to strain when using a long tape measure and that error is L-L0 . Where the error is introduced in inches into the measurement at a L length if the tape is pulled with P N (force) attached contains the question.
In a Torsion test done, the following data were collected: the radius of the specimen was 3mm and the gauge length was 76.2mm. During the elastic zone: T1=0.01N.m, 01-14.76o, T2=17.13N.m, and 02=36.91o. The modulus of rigidity G will be equal to: Select one: a. 26.522 GPa. b. 462.91 MPa. c. 12.94 GPa. d. 44.283 GPa.
Problem 2: A specimen of steel having an initial diameter of 0.503 in was tested in tension using a gauge length of 2 inches. The following data were obtained for the tension. Plot the stress strain data and determine the modulus of elasticity, and the yield strength of the material. Elastic State Load P Ibf Elongation in 1 000 0.0004 2 000 0.0006 3 000 0.0010 4 000 0.0013 7 000 0.0023 8 400 0.0028 8 800 0.0036 9 200 0.0089
Q1- The following data was obtained tensile test ɔn a specimen of 10 mm diameter and gauge length Lo=50 mm: 0 38 | 76.2 92.7 107 149 160.4 | 155 142 124.7 load(KN) | elongation(mm) 0 0.02 0.12 0.25 0.50 2.03 3.55 4.06 5.1 5.84 Using the graphic paper supplied, Plot engineering stress-strain curves, then determine the (ay, ey), (ou , eu), (of,, ef), modulus of elasticity, then detected in the draw ((stroin hardening (m)), (Necking), (uniform plastic region and non-uniform plastic region) and (elastic & plastic) region))?
Problem :- The following data was obtained tensile test on a specimen of 6 mm diameter and gauge length Lo=30 mm: load(KN) 0 40 80 95 90 135 150.2 145 130 120 elongation(mm) 0 0.022 0.13 0.25 0.55 2.01 3.88 4.12 5.22 6 Plot engineering and True (stress-strain) curves, then determine the (oy, ɛy), (ou, ɛu), (of, , ef), ductility, modulus of elasticity. Then select on the drawing ((strain hardening (n)) , (Necking), (uniform plastic region and non-uniform plastic region) and (elastic & plastic) region)?
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…